All Products

Contents - 70ml

Features

Maintains a strong coating which resists friction from wipers, dust, car-wash or cleansers, and lasts 6 times longer than conventional coating agents. The water repellency lasts up about 1 year.

Directions

1. Remove dust and dirt from windscreen with water.

2. Use ‘Glaco Roll On Compound’ in advance for surface preparation.

3. Take cap off and apply on dry windscreen.

4. Press side of bottle to allow fluid out and rub firmly onto windscreen without splashing fluid.
* Do not apply on wet windscreen as it may cause uneven marks to surface.

5. After drying for 5-10 minutes, wipe off with a dry clean towel.

6. Allow drying for at least 12 hours for coating to bond firmly onto windscreen.

Contents - 200g

Features

Fusso Coat 12 Months Wax is a synthetic paint sealant that creates a protective hydrophobic coat on the car's body. It leaves a very smooth and glossy finish. What is by far the most important is the durability! Up to 12 months of beading and sheeting is the reason why Fusso Coat is taking the detailing world by storm. Available in two tone variations to produce best results depending on your vehicle’s paint colour.

✔️ Weather Resistant – Protects the surface of your vehicle from oxidation, discolouration, UV light, acid rain and water

✔️ Anti-Fouling – Does not adhere stain, easy to wash off by just rinsing off dirt, salt, bird droppings, traffic grime and etc

✔️ Strong Water Repellency – Super hydrophobic coating allowing water to sheet off easily

✔️ Gloss – Creates a thick clear, transparent, deep gloss and shine layer on your vehicles surface

✔️ Coats up to 40 vehicles!

Directions

* Make sure that your car colour is compatible with product.

1. Wash and decontaminate car surface.

2. Dampen included applicator with water and take a very thin amount of wax onto the included applicator sponge, spread it thinly and evenly onto car surface.

3. After surface gets dry (2-3 min), wipe off with a dry soft clean towel for finish.

* We recommend you do this process panel by panel (e.g. hood, door, roof, etc.) especially in the summer.

*For best results we recommend buffing off with SOFT99 ‘Wipe Cloth’ and do not wash the car in next 24 hours to allow polymerisation.

Contents - 100ml

Features

Combining the abrasive powder of small, hard particles and big, soft particles, Glaco Glass Compound Roll-On is able to remove the toughest stains made from oily dirt and fluorine film. By just applying the product lightly onto the glass you will see immediate results as the roll-on removes the oil-film with ease. This convenient product can be used as surface preparation just before applying any coating to the glass.

Directions

1. Remove dust and dirt from glass with water, wipe off any water drops remaining on surface.

2. Shake bottle well with cap on and remove plastic seal.

3. Squeeze handle part of bottle to release compound liquid.

4.Polish onto glass until surface stops repelling liquid.

5. Wait for compound to dry, then wash glass clean with water to make a slurry and wipe off.

6. Remove polishing pad from applicator, then wash and dry for future use.

Contents - 40 ml

Features

Repellent prevents water from remaining on the surface by lining the mirror with super-fine, microscopic studs. Spray creates an even coating and shortens the process. Suitable for reverse surfaces such as mirrors and reverse cameras.

Directions

* Clean side mirror/ reverse camera with car shampoo or 'Glaco Compound Roll On'

1. Spray evenly onto surface from a distance of approximately 15cm.
We recommend putting a towel around the mirror while spraying, in order to prevent fluid getting on other parts

2. Allow to dry completely (in the summer for 1 hour, in the winter for 2 hours)

*Do not touch surface when dry.

Contents - 200g

Features

Fusso Coat 12 Months Wax is a synthetic paint sealant that creates a protective hydrophobic coat on the car's body. It leaves a very smooth and glossy finish. What is by far the most important is the durability! Up to 12 months of beading and sheeting is the reason why Fusso Coat is taking the detailing world by storm. Available in two tone variations to produce best results depending on your vehicle’s paint colour.

✔️ Weather Resistant – Protects the surface of your vehicle from oxidation, discolouration, UV light, acid rain and water

✔️ Anti-Fouling – Does not adhere stain, easy to wash off by just rinsing off dirt, salt, bird droppings, traffic grime and etc

✔️ Strong Water Repellency – Super hydrophobic coating allowing water to sheet off easily

✔️ Gloss – Creates a thick clear, transparent, deep gloss and shine layer on your vehicles surface

✔️ Coats up to 40 vehicles!

Directions

* Make sure that your car colour is compatible with product.

1. Wash and decontaminate car surface.

2. Dampen included applicator with water and take a very thin amount of wax onto the included applicator sponge, spread it thinly and evenly onto car surface.

3. After surface gets dry (2-3 min), wipe off with a dry soft clean towel for finish.

* We recommend you do this process panel by panel (e.g. hood, door, roof, etc.) especially in the summer.

*For best results we recommend buffing off with SOFT99 ‘Wipe Cloth’ and do not wash the car in next 24 hours to allow polymerisation.

Contents - 300 ml

Features

Rain Drop coating is formulated to apply onto the entire surface of car body, glass, plastic and chrome. The bazooka trigger spray design allows super-fast product application. Coating protects paint up to 3 months and glass 2 months.

Directions

1. Before use, shake can up and down about 20 times.

2. Wash vehicle to remove any dirt and dust.
No need to completely dry vehicle, can apply product on wet surface.

3. Spray onto wet body/ glass, 1 second will cover about 1m² area.

4. After spraying, immediately spread and wipe foam around surface with a microfiber or cotton towel. Wring out towel regularly.

5. Leave to dry completely for about 5 minutes in hot conditions and 20-30 minutes in winter

! WARNING: DO NOT TURN THE TAB

IF TAB IS TURNED IT WILL RELEASE THE PROPELLANT MAKING PRODUCT REDUNDANT.

TAB IS DESIGNED FOR SAFE DISPOSAL OF SPRAY CAN.

ONLY TURN TAB IN THE UPWARD DIRECTION WHEN PRODUCT IS COMPLETELY USED OR EMPTIED.

THIS WILL ALLOW FOR THE RELEASE OF PROPELLANT FROM THE CAN TO BE SAFELY DISPOSED OF.

Contents - 300 ml

Features

Multi-purpose interior cleaner. Can be used on all surface (fabric, trims, dash, and windows. Super quick drying, leaves no additional finish. Eliminates odour and leaves a refreshing grape fruit scent. Contains ethanol for antibacterial clean.

Directions

When cleaning inside window, seat and floor mat:

1. Remove navy stopper behind trigger.

2. Directly spray onto area and wipe off with dry clean towel.
* Allow liquid to soak, then wipe off
* Wipe off with water if use for cleaning child seat.

When cleaning dash board, handles, trims, plastic and LCD screen

1. Removal navy stopper behind trigger.

2. Spray liquid directly onto clean dry towel and wipe desired area.

Contents - 500ml

Features

pH balanced Iron remover/cleaner designed to dissolve brake dust and iron contaminants upon contact.

Directions

1. Wash off sand, mud or dust prior to spraying.

2. Shake bottle well approx. 20 times, and turn trigger "ON".

3. Spray on surface liberally, initially colourless liquid will gradually turn purple/red within approx. 1-4 minutes.

4. Thoroughly rinse treated surface with a strong stream of water. If solution dry on fully, use a stronger jet of water from a pressure washer to remove film.

* When spray over brake disc, it reacts and changes colour.

Rinse away immediately, if left on too long, may cause bad effects for brake disc.

5. Wipe off with clean towel.

Carry out brake test with low gear 2-3 times after cleaning.

* This product is formulated for wheel.

If use for car body, carefully rinse off with water afterwards.

Contents - 80ml Bottle, 1 x Pad

Features

Newly formulated triple-abrasive particles easily removes scaly spots which conventional compound cleaners cannot. Removes fluorine and sticky oil-film deposits. Restores car's glass close to original transparency. Special application pad is included.

Directions

1. Remove dust and dirt from glass with water, dry off any water remaining on surface.

2. Shake bottle well.

3. Pour liquid onto white side of included pad, begin to polish surface of glass.

4. Finally, wash glass cleanly with water.

.Contents - 300g

Features

The name speaks for itself, extremely high gloss finish wax. King of Gloss creates a thick, heavy gloss coating of synthetic resin that coats your car and gives it the great gloss look similar to transparent nail polish. Available in two tone variations to produce best results depending on your vehicle’s paint colour.

Directions

* Make sure that your car colour is compatible with this product.

* Wash and decontaminate car surface.

1. Take a moderate amount of wax and spread evenly onto car's body using included applicator sponge.

2. After surface gets dry (5-10 minutes), wipe off with a soft clean towel.

*We recommend you do this process panel by panel (e.g. hood, door, roof, etc.) especially in the summer.

*Drying time may be longer in winter .

*For best results we recommend buffing off with SOFT99 ‘Wipe Cloth’.

Contents - 180ml

Features

Product is a spray on mousse that helps reduce condensation on the windows in cold temperatures. All you need to do is spray on leave it for 3 mins and buff it off! The spray can comes in size of 180ml which is enough to last approximately 8-10 windscreen, durability is up to a month.

Directions

1. Clean glass surface prior to application

2. Make sure surface is dry prior to application, you can spray product directly to the glass or on a microfiber cloth

3. Spread evenly, the glass should be full of foam solution, let it on for 3-5 mins

4. Wipe off with another cloth! If necessary you can use paper towel to dry the area.

*Warning do not put near open flames, keep clear away from children

Contents - 110ml

Features

BLACK BLACK creates a thick-film coating on tires and maximizes shine along with super durability. The non-sticky, hard coating prevents dirt from adhering, which helps your car maintain ideal conditions by simply washing. The coating lasts for more than 60 days, and this rubbing type does not splatter over other parts.

Directions

* Be sure to wear protective gloves.
* If the tire is very dirty, remove unwanted residue in advance.
* Do not use this product on wet tires.

1. Shake bottle well and put liquid on black side of included sponge.
Allow enough liquid to soak thoroughly into applicator sponge.

2. Apply to tire and spread evenly across the tire.

Apply repeatedly until desired level of gloss is achieved.

3. Allow coating to dry for approximately 5-10 minutes after applying.

* If liquid gets into unwanted parts, wipe it off immediately with a clean towel or SOFT99 Silicone Off (sold separately).

Contents - 1 cloth (1000mm x 300mm)

Features

The super extra fine microfiber cloth with triangular, cross-section patterns demonstrates a tremendous ability to absorb water and drastically reduces wiping time after washing.

Super extra fine microfiber is effective in removing light levels of unwanted residue.

Big size microfiber cloth 300mm x 1000mm allows for quick easy drying.

Contents - 70 ml

Features

Quick and easy glossy tire shine! Applicator can adjust for tire shape and easy to apply. Can apply up to 3-4 vehicles. High gloss finish with durability up to 6 weeks!

Directions

1. Wash off sand or dust in advance and ensure tire is dry.

2. Shake bottle well.

3. Remove cap and squeeze bottle allowing liquid to soak sponge.

4. Attach sponge side to tire sidewall and spread evenly around tire.

5. Allow to dry for approximately 5-10 minutes.
No need to wipe off.

Contents - 200g

Features

This product is strictly manufactured and tested in Japan and has a high content of first grade Brazilian crystal white carnauba. Throughout manufacturing process it has been cool down naturally unlike conventional wax that cools down immediately with the help of machinery. Cosmetic grade included sponge. No compound is included and is suitable with all colours vehicles.

What comes in the box?

·       Retail packaging

·       Plastic toolkit which contains 3 purpose (Brush, opener and pick)

·       Cosmetic grade applicator sponge

·       Soft rubber bottom, prevent you scratching the car surface if you put in on top your car bodywork

Product is perfect for Show N Shine events!

Directions

1. Remove any dirt on the car bodywork with car shampoo.

2. Apply moderate amount of wax with the sponge included and spread it as even as possible.

3. Allow it to dry for at least 10-15minutes (conditions apply).

4. Use a car detailing grade microfiber cloth to wipe of residue, flip towel if necessary in between process.

*Note for best results:

• We recommend buffing off with SOFT99 ‘Wipe Cloth’.
  
  
• Clay bar after car wash and proper compound process is needed.
  
  
• Sponge is not necessary to be damp when applying wax.
  
  
• In colder weather, it is recommend to allow more time for the wax to cure on the bodywork.
  
  
• If wax caught in badges and tiny gaps, use the tool included (Pick and brush).
  
  
• Applying panel by panel is recommended.

Contents - 300 ml

Features

Replaces IPA wipe down. Essential for surface preparation prior to applying wax or ceramic and glass coating, it will improve the adhesion of the coating to the vehicles surface. The aerosol design allows minimum product usage while spreading to a large area!

✔ Oil, Polish residue and fillers remover
✔ Prep item before applying wax / coating
✔ Replaces IPA wipe down
✔ Improves the adhesion of the surface protective coating
✔ Safe for paint 

Directions

1. Shake bottle well

2. Spray on desired panel and wipe dry with a dry detailing microfiber cloth

3. Expose new clean areas of the towel to avoid smearing the collected wax, oil or compound back onto the vehicle.

Contents - 200g

Features

The Kiwami, which translates to Extreme Gloss, is a great product for those who desire perfect balance between glossy finish and protection. Extreme Gloss is very easy producing a strong beading effect. Making your car paint shiny and smooth as silk! Available in two tone variations to produce best results depending on your vehicle’s paint colour.

Directions

* Make sure that your car colour is compatible with product.

1. Wash and decontaminate car surface.

2. Take a moderate amount of wax and spread evenly onto car's body using included sponge.

3. After surface gets dry (5-10 minutes in 20℃), wipe off with a soft clean towel.

* We recommend you do this process panel by panel (e.g. hood, door, roof, etc.) especially in the summer.

* Drying time may be longer in cold temperature.

*For best results we recommend buffing off with SOFT99 ‘Wipe Cloth’.

 Contents - 200ml Bottle + 8 Base Making Sheets

Features

Coating agent creates super hydrophobic layer onto wheel surface, prevents brake dust adhesion and keeps beautiful condition for a long time. Nano size lotus leaf coating agent prevents adhering water, brake dust and dramatically repels the dirt. All you have to do is wash the wheels, wipe off water, remove oily component with included wipes, then spray and dry. 8 wheels are available to apply in 1 bottle.

Directions

1. Clean wheels by removing dirt with detergent and dry off water.

2. Use included wipes to decontaminate surface ensure all areas are wiped down.

3. Shake bottle well and spray 10cm away from wheel.

Allow to dry 20min in summer (30℃), 60min in winter (10℃)

Do not drive until it gets dry.

* If, surface gets whiten or liquid streak looks uneven, symptom would disappear after time goes by. (If large amount is sprayed, whiten marks will remain)

* Liquid may accumulate at bottom of tires, in case wipe off with wrung towel before it dries. If liquid adheres to other areas, wipe off immediately.

Content - 170g

Features

Solid wax creates a hard coating durable up to 1 month. Enhances tire natural gloss black. Can be used to on tires, convertible leather top, fix scuff marks on exterior bumper and trims.

Directions

Contents - 8 ml

Features

Creates transparent glassy "Nano crystal coating" and ultimate shine on old plastic parts, lasts more than 6 months. Can be used on heated parts such as car or motorcycle's engine cover and silencer. Compatible with unpainted resin parts on car, motorcycle, home electric appliances and even office chairs!

Directions

1. Clean surface ensuring there is no dirt or oil, completely dry prior to applying.

2. Take liquid on black side of included sponge and spread evenly.
* Do not reuse old sponge.

3. Allow to dry for 5 min, wipe off evenly with dry clean towel.
* Do not touch or wet car for 24 hours after applying.
Coating takes 3-4 days to harden completely.

Contents - 1x 50ml Base Cleaner, 1x 8ml Coating Liquid, 2x Sponge, 1x Cloth

Features

Restore headlights, blinkers and taillights. Light one is a multi-step restoration kit that gives your headlight lenses a deep clean and removes haze and discoloration. 

Directions

1. Remove dust and dirt prior to cleaning and application.

2. Shake "Base Cleaner" bottle well, pour liquid onto included cloth and polish lense.

3. Wipe off with clean side of cloth.

4. Shake "Hard Top Coat" bottle well, pour liquid onto included sponge and spread evenly allowing to dry for 1 minute.

* The coating film takes 3-4 days to harden completely. Do not touch or wet the car for 24 hours after applying.

Contents - 1pc

Features

A must have product for all detailers and enthusiast to buff off wax or sealants. ‘Wipe Cloth' has low oil absorption leaving the wax and gloss on the surface of the surface of the vehicle and not absorbing into the cloth. Cloth is washable so can be used repeatedly.

Contents - 2x 50g Clay Bar

Features

SMOOTH EGG Clay Bar gently removes iron powders and deposits from glass/ ceramic coatings.

Directions

1. Wash car, removing sand and dust from the body of vehicle.

2. Knead clay bar by hand until it's soft and flat.

3. Gently slide clay bar over wet surface. * Be sure to knead the bar regularly to expose fresh clay.

Note: Always let the clay bar do the work never add pressure on the surface.
Always lubricate with water or shampoo water when using clay bar on surface.

Contents - 320g

Features

The name speaks for itself, extremely high gloss finish wax. King of Gloss creates a thick, heavy gloss coating of synthetic resin that coats your car and gives it the great gloss look similar to transparent nail polish. Available in two tone variations to produce best results depending on your vehicle’s paint colour.

Directions

* Make sure that your car colour is compatible with this product.

* Wash and decontaminate car surface.

1. Take a moderate amount of wax and spread evenly onto car's body using included applicator sponge.

2. After surface gets dry (5-10 minutes), wipe off with a soft clean towel.

*We recommend you do this process panel by panel (e.g. hood, door, roof, etc.) especially in the summer.

*Drying time may be longer in winter .

*For best results we recommend buffing off with SOFT99 ‘Wipe Cloth’.

Contents - 300g 

Features

Clay bar removes unwanted residue such as iron powder, pitch, tar, bird droppings or dead bugs which cause low gloss and dull on the car. It is more effective to use before polishing, waxing or coating.

Direction

1. Wash car to remove sand or dust.

2. Knead clay bar by hand until it's soft and flat.

3. Rub lightly on car surface and wet area being cleaned.

4. If surface of clay bar gets dirty, refold and continue to use clean surface as needed.

Note: Always let the clay bar do the work never add pressure on the surface.
Always lubricate with water or shampoo water when using clay bar on surface.

Contents - 500 ml

Features

Just spray and wipe to freshen up your vehicle’s bodywork, removing light dust and dirt while applying a highly durable Fusso coating, cleaning and coating in one step! The wax coating is reinforced with fluoro polymers to enhance and extend hydrophobicity for up to 180 days. Perfect for maintaining Fusso Coat. Contents will treat 5 mid-size vehicles.

Directions

* Before applying dirty vehicle, be sure to wash dirt off and dry to avoid scratches.

In cases of staining, use specialised cleaners 'Silicone Off'.

1. Shake well and switch nozzle to ON.

2. Spray surface of vehicle, 1 spray for every 30cm² area.

3. Without allowing to dry, lightly wipe across the surface with a clean, dry towel.

Refold the towel to expose a fresh surface when wiping becomes difficult.

Contents - 230 ml + 1x Cloth

Features

One step cleaning and coating to give leather a hydrophobic protective layers. Protects from dirt and helps retains its natural gloss. Protect your leather upholstery from spillages and stains. Water-based formulation safe for human contact, no unpleasant petrochemical smell. One bottle will treat 20 seats.

Directions

1. Shake well, turn nozzle to 'ON'.

2. Fold cloth into quarters, exposing nappy (fluffy) side.

3. Spray directly onto leather surface from a 10 cm distance. Around 8 shots for seat, and 10 for backrest. Spray onto nappy side of cloth to apply on narrow areas (steering wheel, etc.) or when applying to perforated leather seats.

4. Use dry section of cloth on the nappy side to wipe down surface.
Allow to dry for 30 minutes.

Note: When the desired effect is not achieved, protective coating may be reinforced by repeated application and drying. We recommend reapplying once every 3 months to maintain optimal protection.

Contents - 750 ml

Features

Neutral shampoo which doesn’t damage your car's coated surface. Formulated for maintaining professional or wax-coated vehicles. Included sponge will create bubbles and lather. Product contains NO synthetic cleaning components and abrasive compounds. Natural ingredient, eco-friendly and compatible with ALL colours.

Directions

1. Remove dust and dirt with water.

2. Dilute the liquid 1 cap/ 1L water and apply to included sponge.

3. Wash car gently with sufficient bubbles.

4. Rinse and wipe off remaining water drops with a clean towel.

Contents - 10 Sheets

Features

Dead bugs, bird droppings and tree sap can cause damage to car paint. Not with FUKUPIKA Bugs& Droppings Removal, simply just wiping, removes and completely cleans the car's surface. Compared with conventional cleaning wipes, this wipe makes it possible give the car a nice clean surface finish,without leaving behind any white residue. The products does not contain any petroleum solvent, making FUKUPIKA absolutely eco-friendly!

Directions

1. Take out one sheet from package.

2. Do not rub with excessive force. If removing heavy dirt, wipe and allow cleaner to penetrate dirt, then gently wipe area. Results may vary depending on the contamination and adhesion of dirt.

3. When removing mud, sand, and dust, wipe off surface lightly and finish with a cleaner side of wipe.
* If white residue of cleaner remains on surface, wipe off with a clean wet towel.

4. If whole sheet gets dirty or dry, use another sheet.
* Seal package firmly, in order to prevent sheets from drying out.

Contents - 70 ml

Features

Formulated to coat polycarbonate plastic and glass, such as headlight covers, side visors, tail lamp covers, helmet shields and goggles. Specially designed curved applicator and included microfiber cloth for ease of application. Repels water under air pressure when driving. If you are a motorcycle or race car enthusiast, this product sure is suited for your needs!

Directions

1. Prepare the surfaces by washing and decontaminating.

2. Take off the cap and apply directly with felt applicator.

3. Apply gently ensuring full coverage.

4. Immediately wipe off with included towel.

*No need to wait for drying. Wipe off immediately before liquid gets dry.

Contents - 170mL + Sponge 1pc

Features

Coated agent to prevent fabric seat from dirt and liquid. Just spray and spread with sponge, contain special fluorine (fusso) polymer creating a protective layer on top of your fabric seat. Protects from water based and oil stains as well! High abrasion resistance works approx 3 months*.

Directions

1. Wipe seat with damp towel and vacuum (Do not use any cleaning products).

2. Shake bottle well and turn trigger to on.

3. Spray from a distance of approximately 20cm away from fabric seat
Allow liquid to moisten desired area.

4. Use included sponge to spread liquid in dry area for even coverage.
Spray moderately about 12-15 times per seat.

6. Allow at least 4 hours to dry.

Contents - 400 ml + 1x Brush

Features

Not only cleans fabric seat but also gets rid of bad odours. Antibacterial effect prevents moulds or ticks from occurring, leaving a fresh mint scent behind. Can easily remove dirt, tar, stains or sebum from fabric seats. Included brush used for agitation to remove dirt in fabric. Organic solvent is NOT included, so it is very friendly to people and fabrics.

Directions

1. Turn nozzle to <MIST>.

2. Spray from a distance of approximately 15-20cm from fabric seats or mats.

3. Use included brush to agitate, area sprayed will bubble.

4. Wipe off the bubble and dirt with a clean towel before surface gets dry.

5. Allow to dry completely after cleaning.