Exterior Car Care

Contents - 300ml

Features

This is the evolution of Rain Drop 'Bazooka' - coating both body and glass at the same time. The newly developed Tornado Vortex Head (TV Head) increases speed and ease of application.
Just spray and wipe to activate the G-RAS shield effect, boasting a dramatic improvement over existing technology to provide 5 months of deep shine and hydrophobic protection on the body, and 3 months of rain repellence on glass.
When empty, simply remove the TV Head and replace the cartridge with the large volume refill.

Direction

1. Wash and rinse vehicle thoroughly before use.

2. While locked, shake the can 20 times before spraying evenly onto the wet surface, about 2 seconds per square meter. Wipe up immediately with a clean, dry microfiber cloth, refolding as necessary.

NOTE:

Apply to glass before the body.

If unevenness occurs, thoroughly wash and wring out a microfiber cloth and repeat wiping.
When using on a dry surface, wet and wring out cloth before use.

When applying to grill or wheels, spray onto cloth and wipe surface.

After application, avoid wetting for 1 hour in summer, or 24 hours in winter, to improve coating performance.

In hot conditions (above 35℃), cool can in water for a few minutes before use.

In cold conditions, warm can in tepid water before use.

Contents - 40 ml

Features

Repellent prevents water from remaining on the surface by lining the mirror with super-fine, microscopic studs. Spray creates an even coating and shortens the process. Suitable for reverse surfaces such as mirrors and reverse cameras.

Direction

* Clean side mirror/ reverse camera with car shampoo or 'Glaco Compound Roll On'

1. Spray evenly onto surface from a distance of approximately 15cm.
Tip: We recommend using the packaging or putting a towel around the mirror while spraying, in order to prevent fluid getting on other parts.

2. Allow to dry completely (in the summer for 1 hour, in the winter for 2 hours)

*Do not touch surface when dry.

Contents - 1pc

Features

1. Stand the wiper arm up, tilt the blade slightly so that the wiper rubber faces upward, and slide the wiper blade off while pressing the stopper.

2. Open the cover, insert the clip into the U-hook until it clicks, then close the cover.

3. Operate the wipers about 10 times.

4. Make sure the wipers and spoiler do not touch the body.

5. Operate the wipers on a dry windshield for about 3 minutes.

* In case of the temperature below 10°C may appear the water repellent effect slowly. Then operate the wiper as long as appear the effect. Using the defroster is effective to risen the glass temperature.

* In case of rainy day or wet glass condition may appear the water repellent effect slowly. Then operate the wiper again excepting for rainy day.

* If use window high detergency wash fluid, water repellent effect may be weaken.

* Do not wipe off black powder which adheres on wiper surface. This works the wiper operation smoothly.

* Immediately replace wiper when decrease wiping or water repellent performance.

* Recommend to replace the wiper rubber every half year.

Glaco Wiper New Aero Design

This is a uniquely designed wiper blade that combines the features of an aerodynamic wiper with its low height and excellent design with those of a tournament-style wiper that fits all types of curved glass surfaces and provides stable wiping performance.

Forms a coating film that repels rain

With only about half the wiping time of conventional types (compared to ours), which require wiping for at least 5 minutes when the glass is dry, a coating film is formed on the glass surface that repels rain, providing comfortable rain splash and good visibility on rainy days.

Wedge-shaped cross section to prevent "lifting"!

The wedge-shaped form of the wiper provides downforce from the driving wind, and stable wiping performance is achieved by applying appropriate wiper pressure even at high speeds.

Contents - 1000 ml

Features

Neutral Shampoo has a superb cleaning properties, which prevents dirt and dry suds sticking to the bodywork, even in summer periods you will only need to rinse it once! Shampoo has anion properties which allows it to create crazy amount of suds giving you an additional layer of safe contact with the bodywork. We strongly recommend using the shampoo with our professional ‘PROSPEC Base Conditioner Sponge’ to fully unleash the potential of this product.

Direction

1. Wet sponge first.

2. Pour solution directly onto sponge, or put 5 caps of shampoo into a 20L detailing wash bucket.

3. Lather sponge, if washing with bucket, agitate to allow air to create foams.

4. Glide sponge over body surface in horizontal motion, do not travel backward, compress sponge to release more water and suds.

5. If there is dirt on sponge surface simply squeeze to create suds to lift off dirt.

6. Rinse car after completing process.

7. Wipe off all water drops remaining on surface with a clean or absorption towel.
If water drops remain on surface, it may cause spots or stains.

Contents - 1pc

Features

1. Stand the wiper arm up, tilt the blade slightly so that the wiper rubber faces upward, and slide the wiper blade off while pressing the stopper.

2. Open the cover, insert the clip into the U-hook until it clicks, then close the cover.

3. Operate the wipers about 10 times.

4. Make sure the wipers and spoiler do not touch the body.

5. Operate the wipers on a dry windshield for about 3 minutes.

* In case of the temperature below 10°C may appear the water repellent effect slowly. Then operate the wiper as long as appear the effect. Using the defroster is effective to risen the glass temperature.

* In case of rainy day or wet glass condition may appear the water repellent effect slowly. Then operate the wiper again excepting for rainy day.

* If use window high detergency wash fluid, water repellent effect may be weaken.

* Do not wipe off black powder which adheres on wiper surface. This works the wiper operation smoothly.

* Immediately replace wiper when decrease wiping or water repellent performance.

* Recommend to replace the wiper rubber every half year.

Glaco Wiper New Aero Design

This is a uniquely designed wiper blade that combines the features of an aerodynamic wiper with its low height and excellent design with those of a tournament-style wiper that fits all types of curved glass surfaces and provides stable wiping performance.

Forms a coating film that repels rain

With only about half the wiping time of conventional types (compared to ours), which require wiping for at least 5 minutes when the glass is dry, a coating film is formed on the glass surface that repels rain, providing comfortable rain splash and good visibility on rainy days.

Wedge-shaped cross section to prevent "lifting"!

The wedge-shaped form of the wiper provides downforce from the driving wind, and stable wiping performance is achieved by applying appropriate wiper pressure even at high speeds.

Contents - 80ml Bottle, 1 x Pad

Features

Newly formulated triple-abrasive particles easily removes scaly spots which conventional compound cleaners cannot. Removes fluorine and sticky oil-film deposits. Restores car's glass close to original transparency. Special application pad is included.

Direction

1. Remove dust and dirt from glass with water, dry off any water remaining on surface.

2. Shake bottle well.

3. Pour liquid onto white side of included pad, begin to polish surface of glass.

4. Finally, wash glass cleanly with water.

Contents - 300ml

Features

Rain Drop coating is formulated to apply onto the entire surface of car body, glass, plastic and chrome. The bazooka trigger spray design allows super-fast product application. Coating protects paint up to 3 months and glass 2 months.

Direction

1. Before use, shake can up and down about 20 times.

2. Wash vehicle to remove any dirt and dust.
No need to completely dry vehicle, can apply product on wet surface.

3. Spray onto wet body/ glass, 1 second will cover about 1m² area.

4. After spraying, immediately spread and wipe foam around surface with a microfiber or cotton towel. Wring out towel regularly.

5. Leave to dry completely for about 5 minutes in hot conditions and 20-30 minutes in winter

!warning: do not turn the tab

if tab is turned it will release the propellant making product redundant.

tab is designed for safe disposal of spray can.

only turn tab in the upward direction when product is completely used or emptied.

this will allow for the release of propellant from the can to be safely disposed of.

Contents - 200g

Features

This product is strictly manufactured and tested in Japan and has a high content of first grade Brazilian crystal white carnauba. Throughout manufacturing process it has been cool down naturally unlike conventional wax that cools down immediately with the help of machinery. Cosmetic grade included sponge. No compound is included and is suitable with all colours vehicles.

What comes in the box?

• Retail packaging
• Plastic toolkit which contains 3 purpose (Brush, opener and pick)
• Cosmetic grade applicator sponge
• Soft rubber bottom, prevent you scratching the car surface if you put in on top your car bodywork

Product is perfect for Show N Shine events!

Direction

1. Remove any dirt on the car bodywork with car shampoo.

2. Apply moderate amount of wax with the sponge included and spread it as even as possible.

3. Allow it to dry for at least 10-15minutes (conditions apply).

4. Use a car detailing grade microfiber cloth to wipe of residue, flip towel if necessary in between process.

*Note for best results:

• We recommend buffing off with SOFT99 ‘Wipe Cloth’.
  
• Clay bar after car wash and proper compound process is needed.
  
• Sponge is not necessary to be damp when applying wax.
  
• In colder weather, it is recommend to allow more time for the wax to cure on the bodywork.
  
• If wax caught in badges and tiny gaps, use the tool included pick and brush.
  
• Applying panel by panel is recommended.

Contents - 300ml

Features

Fusso Coat F7 is a liquid sealant based on Fusso fluorine polymers. Product creates a shiny, super hydrophobic coat on the car’s body. Included applicator gives an even and smooth application. F7 is a perfect alternative for those who live in a hurry but still want to have unparalleled paint protection. Product is durable for up to 7 months with regular maintenance.

Direction

1. Prepare vehicle by washing thoroughly with pH neutral shampoo, drying and decontaminating car paint using a clay bar, cleaner or silicone off.

2. Apply a small amount of product onto included sponge.

3. Spread product thinly and evenly, panel by panel, with cross movements.

4. Wait for sealant to dry on surface, until white residue becomes visible.

5. Polish residue with a dry and clean microfiber cloth.
*For best results we recommend bu ffing off with SOFT99 ‘Wipe Cloth’

Contents - 1pc

Features

1. Stand the wiper arm up, tilt the blade slightly so that the wiper rubber faces upward, and slide the wiper blade off while pressing the stopper.

2. Open the cover, insert the clip into the U-hook until it clicks, then close the cover.

3. Operate the wipers about 10 times.

4. Make sure the wipers and spoiler do not touch the body.

5. Operate the wipers on a dry windshield for about 3 minutes.

* In case of the temperature below 10°C may appear the water repellent effect slowly. Then operate the wiper as long as appear the effect. Using the defroster is effective to risen the glass temperature.

* In case of rainy day or wet glass condition may appear the water repellent effect slowly. Then operate the wiper again excepting for rainy day.

* If use window high detergency wash fluid, water repellent effect may be weaken.

* Do not wipe off black powder which adheres on wiper surface. This works the wiper operation smoothly.

* Immediately replace wiper when decrease wiping or water repellent performance.

* Recommend to replace the wiper rubber every half year.

Glaco Wiper New Aero Design

This is a uniquely designed wiper blade that combines the features of an aerodynamic wiper with its low height and excellent design with those of a tournament-style wiper that fits all types of curved glass surfaces and provides stable wiping performance.

Forms a coating film that repels rain

With only about half the wiping time of conventional types (compared to ours), which require wiping for at least 5 minutes when the glass is dry, a coating film is formed on the glass surface that repels rain, providing comfortable rain splash and good visibility on rainy days.

Wedge-shaped cross section to prevent "lifting"!

The wedge-shaped form of the wiper provides downforce from the driving wind, and stable wiping performance is achieved by applying appropriate wiper pressure even at high speeds.

Contents - 1000 ml

Features

High performance pH neutral shampoo removes stubborn dirt in a flash. Will not attract dirt even if the soap dries up during wash. Powerful wash that regains paint clarity. Ultra-fine cleaner particles clean without damaging the paint. Removes minor water spots in one wash.

Direction

1. Remove sand and dust from car with water.

2. Shake bottle well with cap on.

3. Pour 1 or 2 coin size drops of shampoo directly onto a damp sponge, create lather by rubbing sponge.

4. Clean vehicle with sponge.

5. Rinse well with water until all bubbles are gone.

6. Wipe off all water drops remaining on surface with a clean or absorption towel.
If water drops remain on surface, it may cause spots or stains.

Contents - 750ml

Features

Neutral shampoo which doesn’t damage your car's coated surface. Formulated for maintaining professional or wax-coated vehicles. Included sponge will create bubbles and lather. Product contains NO synthetic cleaning components and abrasive compounds. Natural ingredient, eco-friendly and compatible with ALL colours.

Direction

1. Remove dust and dirt with water.

2. Dilute the liquid 1 cap/ 1L water and apply to included sponge.

3. Wash car gently with sufficient bubbles.

4. Rinse and wipe off remaining water drops with a clean towel.

Contents - 1 Sheet (360x360mm)

Features

SMOOTH EGG Smooth Cloth is a microfiber towel which is made with the highest level of Japanese technology at every stage of the process, including the making of an original yarn, knitting, cutting, and sewing. It achieves low friction, works smoothly, excellent water absorption, water retention, and evaporation ability.

Direction

1. Wipe down surface, squeeze cloth dry as needed.

* Wash cloth with tap water and dry thoroughly before storing it.

* If cloth gets dirty, wash with a neutral detergent.

Do not use a bleach and fabric softener.

Contents - 200g

Features

Fusso Coat 12 Months Wax is a synthetic paint sealant that creates a protective hydrophobic coat on the car's body. It leaves a very smooth and glossy finish. What is by far the most important is the durability! Up to 12 months of beading and sheeting is the reason why Fusso Coat is taking the detailing world by storm. Available in two tone variations to produce best results depending on your vehicle’s paint colour.

✔️ Weather Resistant – Protects the surface of your vehicle from oxidation, discolouration, UV light, acid rain and water

✔️ Anti-Fouling – Does not adhere stain, easy to wash off by just rinsing off dirt, salt, bird droppings, traffic grime and etc

✔️ Strong Water Repellency – Super hydrophobic coating allowing water to sheet off easily

✔️ Gloss – Creates a thick clear, transparent, deep gloss and shine layer on your vehicles surface

✔️ Coats up to 40 vehicles!

Direction

* Make sure that your car colour is compatible with product.

1. Wash and decontaminate car surface.

2. Dampen included applicator with water and take a very thin amount of wax onto the included applicator sponge, spread it thinly and evenly onto car surface.

3. After surface gets dry (2-3 min), wipe off with a dry soft clean towel for finish.

* We recommend you do this process panel by panel (e.g. hood, door, roof, etc.) especially in the summer.

*For best results we recommend buffing off with SOFT99 ‘Wipe Cloth’ and do not wash the car in next 24 hours to allow polymerisation.

Contents - 200g

Features

Fusso Coat 12 Months Wax is a synthetic paint sealant that creates a protective hydrophobic coat on the car's body. It leaves a very smooth and glossy finish. What is by far the most important is the durability! Up to 12 months of beading and sheeting is the reason why Fusso Coat is taking the detailing world by storm. Available in two tone variations to produce best results depending on your vehicle’s paint colour.

✔️ Weather Resistant – Protects the surface of your vehicle from oxidation, discolouration, UV light, acid rain and water

✔️ Anti-Fouling – Does not adhere stain, easy to wash off by just rinsing off dirt, salt, bird droppings, traffic grime and etc

✔️ Strong Water Repellency – Super hydrophobic coating allowing water to sheet off easily

✔️ Gloss – Creates a thick clear, transparent, deep gloss and shine layer on your vehicles surface

✔️ Coats up to 40 vehicles!

Directions

* Make sure that your car colour is compatible with product.

1. Wash and decontaminate car surface.

2. Dampen included applicator with water and take a very thin amount of wax onto the included applicator sponge, spread it thinly and evenly onto car surface.

3. After surface gets dry (2-3 min), wipe off with a dry soft clean towel for finish.

* We recommend you do this process panel by panel (e.g. hood, door, roof, etc.) especially in the summer.

*For best results we recommend buffing off with SOFT99 ‘Wipe Cloth’ and do not wash the car in next 24 hours to allow polymerisation.

Contents - 320g

Features

The name speaks for itself, extremely high gloss finish wax. King of Gloss creates a thick, heavy gloss coating of synthetic resin that coats your car and gives it the great gloss look similar to transparent nail polish. Available in two tone variations to produce best results depending on your vehicle’s paint colour.

Directions

* Make sure that your car colour is compatible with this product.

* Wash and decontaminate car surface.

1. Take a moderate amount of wax and spread evenly onto car's body using included applicator sponge.

2. After surface gets dry (5-10 minutes), wipe off with a soft clean towel.

*We recommend you do this process panel by panel (e.g. hood, door, roof, etc.) especially in the summer.

*Drying time may be longer in winter .

*For best results we recommend buffing off with SOFT99 ‘Wipe Cloth’.

Contents - 300g

Features

The name speaks for itself, extremely high gloss finish wax. King of Gloss creates a thick, heavy gloss coating of synthetic resin that coats your car and gives it the great gloss look similar to transparent nail polish. Available in two tone variations to produce best results depending on your vehicle’s paint colour.

Directions

* Make sure that your car colour is compatible with this product.

* Wash and decontaminate car surface.

1. Take a moderate amount of wax and spread evenly onto car's body using included applicator sponge.

2. After surface gets dry (5-10 minutes), wipe off with a soft clean towel.

*We recommend you do this process panel by panel (e.g. hood, door, roof, etc.) especially in the summer.

*Drying time may be longer in winter .

*For best results we recommend buffing off with SOFT99 ‘Wipe Cloth’.

Contents - 100ml

Features

Combining the abrasive powder of small, hard particles and big, soft particles, Glaco Glass Compound Roll-On is able to remove the toughest stains made from oily dirt and fluorine film. By just applying the product lightly onto the glass you will see immediate results as the roll-on removes the oil-film with ease. This convenient product can be used as surface preparation just before applying any coating to the glass.

Direction

1. Remove dust and dirt from glass with water, wipe off any water drops remaining on surface.

2. Shake bottle well with cap on and remove plastic seal.

3. Squeeze handle part of bottle to release compound liquid.

4.Polish onto glass until surface stops repelling liquid.

5. Wait for compound to dry, then wash glass clean with water to make a slurry and wipe off.

6. Remove polishing pad from applicator, then wash and dry for future use.

Content - 170g

Features

Solid wax creates a hard coating durable up to 1 month. Enhances tire natural gloss black. Can be used to on tires, convertible leather top, fix scuff marks on exterior bumper and trims.

Direction

1. Remove dirt from tires, convertible leather top or bumper in advance.

2. Take cap off and take out included applicator sponge.

3. Put wax on desired area and apply it thinly.

4. Allow to dry for approximately (5-10 minutes), polish with a soft cloth to get ultimate, beautiful matte finish.

Contents - 500ml

Features

Water based liquid wax formulated to bring out the "Gloss", "Shine" and "Smoothness" to surface. Added mango scent to reduce chemical odor. Can be used as maintenance liquid for wax coated vehicles.

Direction

1. Wash the car to remove dust, dirt and water component.

2. Shake bottle well, turn nozzle.

3. Spray approximately 50cm² area on dry paintwork.

4. Wipe off immediately dry clean microfiber towel.
* Recommend to use microfiber towel to prevent unevenness.

Content - 500ml

Features

pH balanced Iron remover/cleaner designed to dissolve brake dust and iron contaminants upon contact.

Direction

1. Wash off sand, mud or dust prior to spraying.

2. Shake bottle well approx. 20 times, and turn trigger "ON".

3. Spray on surface liberally, initially colourless liquid will gradually turn purple/red within approx. 1-4 minutes.

4. Thoroughly rinse treated surface with a strong stream of water. If solution dry on fully, use a stronger jet of water from a pressure washer to remove film.

* When spray over brake disc, it reacts and changes colour.

Rinse away immediately, if left on too long, may cause bad effects for brake disc.

5. Wipe off with clean towel.

Carry out brake test with low gear 2-3 times after cleaning.

* This product is formulated for wheel.

If use for car body, carefully rinse off with water afterwards.

Contents - 70 ml

Features

Quick and easy glossy tire shine! Applicator can adjust for tire shape and easy to apply. Can apply up to 3-4 vehicles. High gloss finish with durability up to 6 weeks!

Direction

1. Wash off sand or dust in advance and ensure tire is dry.

2. Shake bottle well.

3. Remove cap and squeeze bottle allowing liquid to soak sponge.

4. Attach sponge side to tire sidewall and spread evenly around tire.

5. Allow to dry for approximately 5-10 minutes.
No need to wipe off.

Contents - 2x 50g Clay Bar

Features

SMOOTH EGG Clay Bar gently removes iron powders and deposits from glass/ ceramic coatings.

Direction

1. Wash car, removing sand and dust from the body of vehicle.

2. Knead clay bar by hand until it's soft and flat.

3. Gently slide clay bar over wet surface. * Be sure to knead the bar regularly to expose fresh clay.

Note: Always let the clay bar do the work never add pressure on the surface.
Always lubricate with water or shampoo water when using clay bar on surface.

Contents - 1pc

Features

1. Stand the wiper arm up, tilt the blade slightly so that the wiper rubber faces upward, and slide the wiper blade off while pressing the stopper.

2. Open the cover, insert the clip into the U-hook until it clicks, then close the cover.

3. Operate the wipers about 10 times.

4. Make sure the wipers and spoiler do not touch the body.

5. Operate the wipers on a dry windshield for about 3 minutes.

* In case of the temperature below 10°C may appear the water repellent effect slowly. Then operate the wiper as long as appear the effect. Using the defroster is effective to risen the glass temperature.

* In case of rainy day or wet glass condition may appear the water repellent effect slowly. Then operate the wiper again excepting for rainy day.

* If use window high detergency wash fluid, water repellent effect may be weaken.

* Do not wipe off black powder which adheres on wiper surface. This works the wiper operation smoothly.

* Immediately replace wiper when decrease wiping or water repellent performance.

* Recommend to replace the wiper rubber every half year.

Glaco Wiper New Aero Design

This is a uniquely designed wiper blade that combines the features of an aerodynamic wiper with its low height and excellent design with those of a tournament-style wiper that fits all types of curved glass surfaces and provides stable wiping performance.

Forms a coating film that repels rain

With only about half the wiping time of conventional types (compared to ours), which require wiping for at least 5 minutes when the glass is dry, a coating film is formed on the glass surface that repels rain, providing comfortable rain splash and good visibility on rainy days.

Wedge-shaped cross section to prevent "lifting"!

The wedge-shaped form of the wiper provides downforce from the driving wind, and stable wiping performance is achieved by applying appropriate wiper pressure even at high speeds.

Contents - 70ml

Features

Maintains a strong coating which resists friction from wipers, dust, car-wash or cleansers, and lasts 6 times longer than conventional coating agents. The water repellency lasts up about 1 year.

Direction

1. Remove dust and dirt from windscreen with water.

2. Use ‘Glaco Roll On Compound’ in advance for surface preparation.

3. Take cap off and apply on dry windscreen.

4. Press side of bottle to allow fluid out and rub firmly onto windscreen without splashing fluid.
* Do not apply on wet windscreen as it may cause uneven marks to surface.

5. After drying for 5-10 minutes, wipe off with a dry clean towel.

6. Allow drying for at least 12 hours for coating to bond firmly onto windscreen.

Applications

Contents - 200ml, 2x Applicator Pad, 2x Microfiber Towel

Features - 2 Years Durability Hydrophilic Coating

H-7 was originally formulated for vending machines in Japan in the early 2000s and later found its use to protect objects in harsh environments: vehicles, wheels, marine vessels, vending machines, trains, signage, aircrafts, and other outside equipment and its housing. The product creates a tough, silicon-based coating that forms a hard glass layer to protect objects against corrosion from rain, salt, mud, chemicals, UV radiation, and even light abrasion. Excellent self cleaning effect with its hydrophilic properties and is absolutely safe for the paint. Can be used on gloss and matte surfaces. Coating provides superior waterproof and anti-rust functions, which makes it a suitable choice of coating for items that are installed outdoor.

✔️ Weather Resistant – Protects the surface of your vehicle from oxidation, discolouration, UV light, acid rain and water

✔️ Anti-Fouling – Does not adhere stain, easy to wash off by just rinsing off dirt, salt, bird droppings, traffic grime and etc

✔️ Hardness – Excellent resistance against micro scratches caused by wind dust and dirt

✔️ Adhesion – Adheres tightly to paint allowing coat to have a long lasting durability

✔️ Super Hydrophilic – Excellent water sheeting effect, prevents water stain adhesion

FIELD TEST RESULTS

Drainage Performance Test – Water on hood receding

Less Frequent Visit to Car Wash

3 Months  Outside Exposure Test comparison to generic body glass coating

 
VENDING MACHINE (6 MONTHS AFTER APPLICATION)

MARINE BOAT (12 MONTHS AFTER APPLICATION)

OUT DOOR CONDENSER UNIT (34 MONTHS AFTER APPLICATION)

 
Direction

1. Completely remove grease and dirt from areas to be treated. If a cleaning agent or water is used, allow to dry completely.

2. Use Silicone Off to wipe down any remaining residual this will allow a stronger bond between the surface and coating.

3. Apply liquid to the white surface of the included sponge. Apply evenly to the surface, leaving no untreated or poorly covered areas. Use each sponge for only one application (do not reuse a sponge that has hardened).

4. Allow to dry for approximately 5 minutes, and wipe down lightly with the included cloth.

5. After coating, leave to cure in a dry place for 12 hours.

CAUTION!!!

Contents - 300g

Features

Dark & Black Wax creates a long-lasting coating of wax that brings out the deep shine of dark solid colors like black, deep blue, and brown.

Direction

*Make sure that your colour is compatible with this product.
* Wash and decontaminate car surface.

1. Take a moderate amount of wax and spread evenly onto car's body using included applicator sponge.

2. After surface gets dry (5-10 minutes), wipe it off with a soft clean towel.
Make sure to finish entire process. If left unfinished, may cause spots or unevenness.

3. Seal can container in order to prevent fluid from evaporating.
Wash hands well with soap after use.
*For best results we recommend buffing off with SOFT99 ‘Wipe Cloth’.

Contents - 350g

Features

By just lightly applying this product, you will remove dirt and apply a wax coating simultaneously, bringing out the shiny whiteness of the body paint. Solid white colour only. Only suitable for single-stage paint i.e. very-light coloured paint (like trade vans and etc.) it will not improve the appearance of clear top coat.

Direction

*Make sure that your colour is compatible with this product.
* Wash and decontaminate car surface.

1. Take a moderate amount of wax and spread evenly onto car's body using included applicator sponge.

2. Rub firmly to remove heavier stains like dirt, tar, and pitch.

3. After surface gets dry (5-10 minutes), wipe it off with a soft clean towel.
Make sure to finish entire process. If left unfinished, may cause spots or unevenness.

4. Seal can container in order to prevent fluid from evaporating.
Wash hands well with soap after use.
*For best results we recommend buffing off with SOFT99 ‘Wipe Cloth’.

Contents - 1pc

Features

1. Stand the wiper arm up, tilt the blade slightly so that the wiper rubber faces upward, and slide the wiper blade off while pressing the stopper.

2. Open the cover, insert the clip into the U-hook until it clicks, then close the cover.

3. Operate the wipers about 10 times.

4. Make sure the wipers and spoiler do not touch the body.

5. Operate the wipers on a dry windshield for about 3 minutes.

* In case of the temperature below 10°C may appear the water repellent effect slowly. Then operate the wiper as long as appear the effect. Using the defroster is effective to risen the glass temperature.

* In case of rainy day or wet glass condition may appear the water repellent effect slowly. Then operate the wiper again excepting for rainy day.

* If use window high detergency wash fluid, water repellent effect may be weaken.

* Do not wipe off black powder which adheres on wiper surface. This works the wiper operation smoothly.

* Immediately replace wiper when decrease wiping or water repellent performance.

* Recommend to replace the wiper rubber every half year.

Glaco Wiper New Aero Design

This is a uniquely designed wiper blade that combines the features of an aerodynamic wiper with its low height and excellent design with those of a tournament-style wiper that fits all types of curved glass surfaces and provides stable wiping performance.

Forms a coating film that repels rain

With only about half the wiping time of conventional types (compared to ours), which require wiping for at least 5 minutes when the glass is dry, a coating film is formed on the glass surface that repels rain, providing comfortable rain splash and good visibility on rainy days.

Wedge-shaped cross section to prevent "lifting"!

The wedge-shaped form of the wiper provides downforce from the driving wind, and stable wiping performance is achieved by applying appropriate wiper pressure even at high speeds.

Contents - 200g

Features

By just applying the wax with included microfiber cloth, Mirror Shine WAX will create a mirror-like clear gloss and shine. This solid wax creates a thick-film coating without the need to wipe or dry, and it lasts for up to 3 months. May be used on plastic parts as well, such as headlight covers, car visor and tail lamps.

Direction

*Make sure car colour is compatible with this product.
* Wash and decontaminate car surface.

1. Take wax using included cloth and apply evenly to car surface.

2. All you need to do is polish firmly on the surface, there is no need to wipe off.

*Make sure to finish the entire process. If left unfinished, it may cause spots or unevenness.
*For best results we recommend buffing off with SOFT99 ‘Wipe Cloth’.

Contents - 300 ml

Features

Replaces IPA wipe down. Essential for surface preparation prior to applying wax or ceramic and glass coating, it will improve the adhesion of the coating to the vehicles surface. The aerosol design allows minimum product usage while spreading to a large area!

✔ Oil, Polish residue and fillers remover
✔ Prep item before applying wax / coating
✔ Replaces IPA wipe down
✔ Improves the adhesion of the surface protective coating
✔ Safe for paint 

Direction

1. Shake bottle well

2. Spray on desired panel and wipe dry with a dry detailing microfiber cloth

3. Expose new clean areas of the towel to avoid smearing the collected wax, oil or compound back onto the vehicle.

Contents - 200g

Features

Direction

Note: Use only on specified colours. Apply to a washed and thoroughly dried car. In hot conditions, work panel-by-panel to avoid over-curing. Curing time may be longer in cold conditions.

1. Take a moderate amount of wax onto the included sponge, and spread it evenly over the body of the vehicle.

2. Increase pressure to remove stubborn dirt and stains.

3. After drying for between 5 and 15 minutes, buff off with a soft clean towel. Be sure to remove completely and promptly to avoid damaging the paintwork.