Engine & Plastic Trim

Contents - 8ml

Features

Creates transparent glassy "Nano crystal coating" and ultimate shine on old plastic parts, lasts more than 6 months. Can be used on heated parts such as car or motorcycle's engine cover and silencer. Compatible with unpainted resin parts on car, motorcycle, home electric appliances and even office chairs!

Direction

1. Clean surface ensuring there is no dirt or oil, completely dry prior to applying.

2. Take liquid on black side of included sponge and spread evenly.
* Do not reuse old sponge.

3. Allow to dry for 5 min, wipe off evenly with dry clean towel.
* Do not touch or wet car for 24 hours after applying.
Coating takes 3-4 days to harden completely.

Contents - 1x Coating Agent bottle (15mL), 2x Hard Sponge, 2x Soft Sponge, 3x Silicone off Wipes Sheets, 2x Gloves

Features

Bring the life back to faded plastic and rubber trim! This treatment restores the deep darkness, natural gloss, and rich texture of black trim to revitalize your vehicle. The unique coating liquid penetrates into the surface and polymerizes to form a flexible yet glossy surface, making it suitable for restoring both hard plastic and soft rubber!

Direction

Note: Apply only to clean, dry, unpainted plastic and rubber.

1. First clean and degrease the area to be treated using the included ‘Silicone Off’ degreasing sheets.

Note: Some textured plastics may pick up fibers from the sheet. Remove these before proceeding. To prevent the sheets from drying out, firmly seal the package between uses.

2. Cut sponge to suitable size for area to be treated. The black sponge is for hard plastic, the white sponge is for soft rubber. Apply a small amount of the liquid (green label), and spread thinly and evenly across the surface to be treated.

Note: Some rubber parts may absorb the liquid. Keep applying until enough liquid remains.

3. After drying for around 5 minutes, use a fresh sheet to lightly wipe up the surface for an even finish. If left for too long, the excess will not be possible to remove.

Note: Do not touch or wet for 24 hours. Do not reuse sponges that have hardened. If the liquid unintentionally comes into contact with another surface, wipe off immediately.

Contents - Abrasive 80ml, Ultrafine pad L ×1, Ultrafine pad S ×1, Compound Sponge ×1

Features

The high-gloss black plastic known as piano black shows scratches very easily, and can show age much more quickly than paint or other areas of the vehicle. This kit makes it easy to restore painted and unpainted piano black and other high-gloss plastics by hand, refining them to a near new condition.

Direction

Note: Be sure to thoroughly clean and thoroughly dry the area to be treated, and mask off neighbouring areas. Use a scratch removal compound (sold separately) with the compound sponge to remove any deep scratches beforehand.

1. With the cap closed, shake the bottle well.

2. Choose an ultrafine pad size appropriate or comfortable. Apply a moderate amount of compound to the black surface of the pad. Polish the surface while spreading the liquid in horizontal and vertical motions. Aim work on one 30×30 cm area at a time.

3. After polishing, remove any masking and wipe up any residue with a soft, clean towel.

Contents - 40ml Base Cleaner, 8ml Coating Liquid, 4 x Special Sheets, 4 x Sponge

Features

Restoration for unpainted resin parts such as a bumper or around wipers. Included 'Liquid Binder' removes dirt marks from the surface of resin parts, and 'Hard Clear Coat', creating a Silicon-based thick hard film coating.

Direction

1. Remove dirt, oil and any other unwanted residues from surface.

Dry completely.

2. Apply a small amount of “Liquid Binder” onto included sheet, then spread thinly and evenly.

3. Wipe off with clean side of sheet.

4. Detach one sponge, apply “Hard Clear Coat” onto black side of included sponge and spread evenly.

5. Do not touch or wet surface for 24 hours.

Contents - 300ml

Features

It removes dirt such as carbon or sludge accumulating on the inside of the injector or combustion chamber, and restores the engine power.

Direction

1. Leave the car idling for approximately 5-6 minutes to warm the engine.

2. Stop the engine and loosen the rubber hose a bit to make enough space to insert the tube to let you spray toward the throttle chamber.

3. Turn on the engine and use a whole bottle while keeping idling at about 2000 times engine rotation.

4. Meanwhile leave it for approximately 5-6 minutes after the engine stops, and reset the rubber hose. Afterward turn on the engine and snap until white smoke is not produced.

* Be sure not to spray over the Air flow meter.