13 products
13 products
13 products
Silicone Off 300ml
Panel Wipe
09170
Regular price $19.00Contents - 300 ml
Features
Replaces IPA wipe down. Essential for surface preparation prior to applying wax or ceramic and glass coating, it will improve the adhesion of the coating to the vehicles surface. The aerosol design allows minimum product usage while spreading to a large area!
✔ Oil, Polish residue and fillers remover
✔ Prep item before applying wax / coating
✔ Replaces IPA wipe down
✔ Improves the adhesion of the surface protective coating
✔ Safe for paint
Directions
1. Shake bottle well
2. Spray on desired panel and wipe dry with a dry detailing microfiber cloth
3. Expose new clean areas of the towel to avoid smearing the collected wax, oil or compound back onto the vehicle.
Compound Set
10000
Regular price $90.00Features
Cutting • Polishing • Finishing
Abrasives for correcting and finishing automobile paint
Formulated for efficient correction (scratch removal), polishing, and high-gloss finishing of automobile paint. Suitable for machine polish only
Cutting Compound 300ml
Remove scratches, orange peel, and sandpaper marks with Cutting Compound
Wool buff pad @ 1800rpm
Polishing Compound 300ml
Remove marks from Cutting and bring to a gloss with Polishing CompoundSponge/Euro foam buff pad @ 1500rpm
(if sandpaper marks remain, use wool)
Finishing Compound 300ml
If desired, bring paintwork up to perfection with clear gloss then finish with Finishing Compound
Sponge/Euro 'finishing' foam buff pad @ 1300rpm
Excellent properties with results:
✔ Suitable for all types of automobile paint
✔ Fine ceramic abrasive is highly refined to prevent scratches, marring, and blurring
✔ New anti-clogging, low dust formula improves working conditions
✔ Can be used as a two- or three-step process, as needed
✔ Contain no silicone, gloss-enhancers, or any other unnecessary additives
H-7 (200ml)
Ceramic Coating
10084
Regular price $250.00Applications
Contents - 200ml, 2x Applicator Pad, 2x Microfiber Towel
Features - 2 Years Durability Hydrophilic Coating
H-7 was originally formulated for vending machines in Japan in the early 2000s and later found its use to protect objects in harsh environments: vehicles, wheels, marine vessels, vending machines, trains, signage, aircrafts, and other outside equipment and its housing. The product creates a tough, silicon-based coating that forms a hard glass layer to protect objects against corrosion from rain, salt, mud, chemicals, UV radiation, and even light abrasion. Excellent self cleaning effect with its hydrophilic properties and is absolutely safe for the paint. Can be used on gloss and matte surfaces. Coating provides superior waterproof and anti-rust functions, which makes it a suitable choice of coating for items that are installed outdoor.
✔️ Weather Resistant – Protects the surface of your vehicle from oxidation, discolouration, UV light, acid rain and water
✔️ Anti-Fouling – Does not adhere stain, easy to wash off by just rinsing off dirt, salt, bird droppings, traffic grime and etc
✔️ Hardness – Excellent resistance against micro scratches caused by wind dust and dirt
✔️ Adhesion – Adheres tightly to paint allowing coat to have a long lasting durability
✔️ Super Hydrophilic – Excellent water sheeting effect, prevents water stain adhesion
Drainage Performance Test – Water on hood receding
Less Frequent Visit to Car Wash
3 Months Outside Exposure Test comparison to generic body glass coating
VENDING MACHINE (6 MONTHS AFTER APPLICATION)
Directions
1. Completely remove grease and dirt from areas to be treated. If a cleaning agent or water is used, allow to dry completely.
2. Use Silicone Off to wipe down any remaining residual this will allow a stronger bond between the surface and coating.
3. Apply liquid to the white surface of the included sponge. Apply evenly to the surface, leaving no untreated or poorly covered areas. Use each sponge for only one application (do not reuse a sponge that has hardened).
4. Allow to dry for approximately 5 minutes, and wipe down lightly with the included cloth.
5. After coating, leave to cure in a dry place for 12 hours.
CAUTION!!!
! As it dries, uncoated areas will become obvious. If there are any uncoated areas left behind, reapply to coat to the area.
! Wipe off liquid within 20 min. after applied. If you leave longer, wiping will be hard and may cause an uneven finish. Application should be avoided when the surface to be coated is hot, because the liquid dries immediately and may cause an uneven finish.
H-7 (100ml)
Ceramic Coating
10297
Regular price $160.00Applications
Contents - 100ml, 2x Applicator Pad, 2x Microfiber Towel
Features - 2 Years Durability Hydrophilic Coating
H-7 was originally formulated for vending machines in Japan in the early 2000s and later found its use to protect objects in harsh environments: vehicles, wheels, marine vessels, vending machines, trains, signage, aircrafts, and other outside equipment and its housing. The product creates a tough, silicon-based coating that forms a hard glass layer to protect objects against corrosion from rain, salt, mud, chemicals, UV radiation, and even light abrasion. Excellent self cleaning effect with its hydrophilic properties and is absolutely safe for the paint. Can be used on gloss and matte surfaces. Coating provides superior waterproof and anti-rust functions, which makes it a suitable choice of coating for items that are installed outdoor.
✔️ Weather Resistant – Protects the surface of your vehicle from oxidation, discolouration, UV light, acid rain and water
✔️ Anti-Fouling – Does not adhere stain, easy to wash off by just rinsing off dirt, salt, bird droppings, traffic grime and etc
✔️ Hardness – Excellent resistance against micro scratches caused by wind dust and dirt
✔️ Adhesion – Adheres tightly to paint allowing coat to have a long lasting durability
✔️ Super Hydrophilic – Excellent water sheeting effect, prevents water stain adhesion
Drainage Performance Test – Water on hood receding
Less Frequent Visit to Car Wash
3 Months Outside Exposure Test comparison to generic body glass coating
VENDING MACHINE (6 MONTHS AFTER APPLICATION)
Directions
1. Completely remove grease and dirt from areas to be treated. If a cleaning agent or water is used, allow to dry completely.
2. Use Silicone Off to wipe down any remaining residual this will allow a stronger bond between the surface and coating.
3. Apply liquid to the white surface of the included sponge. Apply evenly to the surface, leaving no untreated or poorly covered areas. Use each sponge for only one application (do not reuse a sponge that has hardened).
4. Allow to dry for approximately 5 minutes, and wipe down lightly with the included cloth.
5. After coating, leave to cure in a dry place for 12 hours.
CAUTION!!!
! As it dries, uncoated areas will become obvious. If there are any uncoated areas left behind, reapply to coat to the area.
! Wipe off liquid within 20 min. after applied. If you leave longer, wiping will be hard and may cause an uneven finish. Application should be avoided when the surface to be coated is hot, because the liquid dries immediately and may cause an uneven finish.
H-7 (50ml)
Ceramic Coating
00542
Regular price $100.00Applications
Contents - 50ml, 1x Applicator Pad, 2x Application cloth, 1x Microfiber Towel, 1x Pasteur Pipette
Features - 2 Years Durability Hydrophilic Coating
H-7 was originally formulated for vending machines in Japan in the early 2000s and later found its use to protect objects in harsh environments: vehicles, wheels, marine vessels, vending machines, trains, signage, aircrafts, and other outside equipment and its housing. The product creates a tough, silicon-based coating that forms a hard glass layer to protect objects against corrosion from rain, salt, mud, chemicals, UV radiation, and even light abrasion. Excellent self cleaning effect with its hydrophilic properties and is absolutely safe for the paint. Can be used on gloss and matte surfaces. Coating provides superior waterproof and anti-rust functions, which makes it a suitable choice of coating for items that are installed outdoor.
✔️ Weather Resistant – Protects the surface of your vehicle from oxidation, discolouration, UV light, acid rain and water
✔️ Anti-Fouling – Does not adhere stain, easy to wash off by just rinsing off dirt, salt, bird droppings, traffic grime and etc
✔️ Hardness – Excellent resistance against micro scratches caused by wind dust and dirt
✔️ Adhesion – Adheres tightly to paint allowing coat to have a long lasting durability
✔️ Super Hydrophilic – Excellent water sheeting effect, prevents water stain adhesion
Drainage Performance Test – Water on hood receding
Less Frequent Visit to Car Wash
3 Months Outside Exposure Test comparison to generic body glass coating
VENDING MACHINE (6 MONTHS AFTER APPLICATION)
Directions
1. Completely remove grease and dirt from areas to be treated. If a cleaning agent or water is used, allow to dry completely.
2. Use Silicone Off to wipe down any remaining residual this will allow a stronger bond between the surface and coating.
3. Apply liquid to the white surface of the included sponge. Apply evenly to the surface, leaving no untreated or poorly covered areas. Use each sponge for only one application (do not reuse a sponge that has hardened).
4. Allow to dry for approximately 5 minutes, and wipe down lightly with the included cloth.
5. After coating, leave to cure in a dry place for 12 hours.
CAUTION!!!
! As it dries, uncoated areas will become obvious. If there are any uncoated areas left behind, reapply to coat to the area.
! Wipe off liquid within 20 min. after applied. If you leave longer, wiping will be hard and may cause an uneven finish. Application should be avoided when the surface to be coated is hot, because the liquid dries immediately and may cause an uneven finish.
Creamy Shampoo & Snow Foam 5L
Shampoo
10336
Regular price $99.00Contents - 5000ml
Features
Powerful, pH-neutral, and compound-free, this high-powered shampoo lathers into a thick, creamy foam that just melts the dirt away. Professional size and packaging. Despite its powerful foaming ability, this product has been designed with ease of rinsing in mind. May be used on coated vehicles, diluted 1:50. Compatible with water- and air-driven foamers.
Finishing Compound
Finishing
10322
Regular price $35.00Contents - 300ml
Features
If desired, bring paintwork up to perfection with clear gloss then finish with Finishing Compound
✔ Suitable for all types of automobile paint
✔ Contain no silicone, gloss-enhancers, or any other unnecessary additives
Recommended Pad & Speed
Sponge/Euro 'finishing' foam buff pad @ 1300rpm
Cutting Compound
Cutting
10320
Regular price $35.00Contents - 300ml
Features
Remove scratches, orange peel, and sandpaper marks with Cutting Compound
✔ Suitable for all types of automobile paint
✔ Fine ceramic abrasive is highly refined to prevent scratches, marring, and blurring
✔ New anti-clogging, low dust formula improves working conditions
✔ Can be used as a two- or three-step process, as needed
✔ Contain no silicone, gloss-enhancers, or any other unnecessary additives
Recommended Pad & Speed
Wool buff pad @ 1800rpm
Claryfying Compound 1L
Claryfying Compound
10326
Regular price $65.00Contents - 1000ml
Features
This versatile, full-spectrum compound for professionals is designed for efficient correction (scratch removal),polishing, and high-gloss finishing of automobile paint. It is optimized for machine polishing,but may also be used by hand.
For cut use a wool pad and foam pad to finish.