Cleaning & Surface Preparation

Contents - 100ml

Features

Combining the abrasive powder of small, hard particles and big, soft particles, Glaco Glass Compound Roll-On is able to remove the toughest stains made from oily dirt and fluorine film. By just applying the product lightly onto the glass you will see immediate results as the roll-on removes the oil-film with ease. This convenient product can be used as surface preparation just before applying any coating to the glass.

Directions

1. Remove dust and dirt from glass with water, wipe off any water drops remaining on surface.

2. Shake bottle well with cap on and remove plastic seal.

3. Squeeze handle part of bottle to release compound liquid.

4.Polish onto glass until surface stops repelling liquid.

5. Wait for compound to dry, then wash glass clean with water to make a slurry and wipe off.

6. Remove polishing pad from applicator, then wash and dry for future use.

Contents - 300 ml

Features

Multi-purpose interior cleaner. Can be used on all surface (fabric, trims, dash, and windows. Super quick drying, leaves no additional finish. Eliminates odour and leaves a refreshing grape fruit scent. Contains ethanol for antibacterial clean.

Directions

When cleaning inside window, seat and floor mat:

1. Remove navy stopper behind trigger.

2. Directly spray onto area and wipe off with dry clean towel.
* Allow liquid to soak, then wipe off
* Wipe off with water if use for cleaning child seat.

When cleaning dash board, handles, trims, plastic and LCD screen

1. Removal navy stopper behind trigger.

2. Spray liquid directly onto clean dry towel and wipe desired area.

Contents - 500ml

Features

pH balanced Iron remover/cleaner designed to dissolve brake dust and iron contaminants upon contact.

Directions

1. Wash off sand, mud or dust prior to spraying.

2. Shake bottle well approx. 20 times, and turn trigger "ON".

3. Spray on surface liberally, initially colourless liquid will gradually turn purple/red within approx. 1-4 minutes.

4. Thoroughly rinse treated surface with a strong stream of water. If solution dry on fully, use a stronger jet of water from a pressure washer to remove film.

* When spray over brake disc, it reacts and changes colour.

Rinse away immediately, if left on too long, may cause bad effects for brake disc.

5. Wipe off with clean towel.

Carry out brake test with low gear 2-3 times after cleaning.

* This product is formulated for wheel.

If use for car body, carefully rinse off with water afterwards.

Contents - 80ml Bottle, 1 x Pad

Features

Newly formulated triple-abrasive particles easily removes scaly spots which conventional compound cleaners cannot. Removes fluorine and sticky oil-film deposits. Restores car's glass close to original transparency. Special application pad is included.

Directions

1. Remove dust and dirt from glass with water, dry off any water remaining on surface.

2. Shake bottle well.

3. Pour liquid onto white side of included pad, begin to polish surface of glass.

4. Finally, wash glass cleanly with water.

Contents - 300 ml

Features

Replaces IPA wipe down. Essential for surface preparation prior to applying wax or ceramic and glass coating, it will improve the adhesion of the coating to the vehicles surface. The aerosol design allows minimum product usage while spreading to a large area!

✔ Oil, Polish residue and fillers remover
✔ Prep item before applying wax / coating
✔ Replaces IPA wipe down
✔ Improves the adhesion of the surface protective coating
✔ Safe for paint 

Directions

1. Shake bottle well

2. Spray on desired panel and wipe dry with a dry detailing microfiber cloth

3. Expose new clean areas of the towel to avoid smearing the collected wax, oil or compound back onto the vehicle.

Contents - 2x 50g Clay Bar

Features

SMOOTH EGG Clay Bar gently removes iron powders and deposits from glass/ ceramic coatings.

Directions

1. Wash car, removing sand and dust from the body of vehicle.

2. Knead clay bar by hand until it's soft and flat.

3. Gently slide clay bar over wet surface. * Be sure to knead the bar regularly to expose fresh clay.

Note: Always let the clay bar do the work never add pressure on the surface.
Always lubricate with water or shampoo water when using clay bar on surface.

Contents - 10 Sheets

Features

Dead bugs, bird droppings and tree sap can cause damage to car paint. Not with FUKUPIKA Bugs& Droppings Removal, simply just wiping, removes and completely cleans the car's surface. Compared with conventional cleaning wipes, this wipe makes it possible give the car a nice clean surface finish,without leaving behind any white residue. The products does not contain any petroleum solvent, making FUKUPIKA absolutely eco-friendly!

Directions

1. Take out one sheet from package.

2. Do not rub with excessive force. If removing heavy dirt, wipe and allow cleaner to penetrate dirt, then gently wipe area. Results may vary depending on the contamination and adhesion of dirt.

3. When removing mud, sand, and dust, wipe off surface lightly and finish with a cleaner side of wipe.
* If white residue of cleaner remains on surface, wipe off with a clean wet towel.

4. If whole sheet gets dirty or dry, use another sheet.
* Seal package firmly, in order to prevent sheets from drying out.

Contents - 300g 

Features

Clay bar removes unwanted residue such as iron powder, pitch, tar, bird droppings or dead bugs which cause low gloss and dull on the car. It is more effective to use before polishing, waxing or coating.

Direction

1. Wash car to remove sand or dust.

2. Knead clay bar by hand until it's soft and flat.

3. Rub lightly on car surface and wet area being cleaned.

4. If surface of clay bar gets dirty, refold and continue to use clean surface as needed.

Note: Always let the clay bar do the work never add pressure on the surface.
Always lubricate with water or shampoo water when using clay bar on surface.

Contents - 750 ml

Features

Neutral shampoo which doesn’t damage your car's coated surface. Formulated for maintaining professional or wax-coated vehicles. Included sponge will create bubbles and lather. Product contains NO synthetic cleaning components and abrasive compounds. Natural ingredient, eco-friendly and compatible with ALL colours.

Directions

1. Remove dust and dirt with water.

2. Dilute the liquid 1 cap/ 1L water and apply to included sponge.

3. Wash car gently with sufficient bubbles.

4. Rinse and wipe off remaining water drops with a clean towel.

Contents - 500ml

Features

Gel type spray glass cleaner lets you clean the glass easily without any liquid or water droplets leaving residue. The cleaning components are held in the gel, giving time to penetrate dirt and increase the effectiveness of cleaning stubborn dirt, such as bird droppings. Also suitable for use on mirrors, unpainted plastic, and rubber parts.

Directions

1. Turn the spray nozzle to “ON”.

2. Without shaking, spray onto the glass surface from 15 – 20cm away, then immediately wipe around the glass with a clean, dry towel.

3. Wipe up the dirt, changing to a fresh surface of the towel when necessary.

*If some residue remains on the glass, wipe again with a clean towel.

Contents - 400 ml + 1x Brush

Features

Not only cleans fabric seat but also gets rid of bad odours. Antibacterial effect prevents moulds or ticks from occurring, leaving a fresh mint scent behind. Can easily remove dirt, tar, stains or sebum from fabric seats. Included brush used for agitation to remove dirt in fabric. Organic solvent is NOT included, so it is very friendly to people and fabrics.

Directions

1. Turn nozzle to <MIST>.

2. Spray from a distance of approximately 15-20cm from fabric seats or mats.

3. Use included brush to agitate, area sprayed will bubble.

4. Wipe off the bubble and dirt with a clean towel before surface gets dry.

5. Allow to dry completely after cleaning.

Contents - 1000 ml

Features

High performance pH neutral shampoo removes stubborn dirt in a flash. Will not attract dirt even if the soap dries up during wash. Powerful wash that regains paint clarity. Ultra-fine cleaner particles clean without damaging the paint. Removes minor water spots in one wash.

Directions

1. Remove sand and dust from car with water.

2. Shake bottle well with cap on.

3. Pour 1 or 2 coin size drops of shampoo directly onto a damp sponge, create lather by rubbing sponge.

4. Clean vehicle with sponge.

5. Rinse well with water until all bubbles are gone.

6. Wipe off all water drops remaining on surface with a clean or absorption towel.
If water drops remain on surface, it may cause spots or stains.

Contents - 12 Sheets (350mm x 300mm)

Features

✔ QUICK EASY CLEAN & WAX CAR
✔ NO RINSING OR DRYING REQUIRED
✔ WATER REPELLENCY UP TO 1 MONTH
✔ CAN BE USE ON CERAMIC COATED VEHICLES

Triple-layer sheet for easy washing and waxing. Central layer designed for absorbing dirt to keep the outer layers clean. Helps prevent scratches and supports the structure of the  outer layers to glide lightly and effortlessly over your vehicle. Leaves your car clean, shiny and with water repellency up to 1 months.

Directions

1. Open the front flap, and pull out one wipe.

2. Fold the sheet into quarters and lightly wipe down the body of the vehicle.  Keep refolding the wipe to expose fresh surfaces and avoid spreading any dirt.

3. In particularly dirty areas, gently wipe off the dirt, then with a fresh surface of the sheet wipe of again.

4. If the entire wipe is dirty or becomes dried out, please use a fresh sheet.

5. Discard wipes after use.

NOTE: CLOSE AFTER USE TO KEEP WIPES MOIST.

Features

Cutting • Polishing • Finishing

Abrasives for correcting and finishing automobile paint

Formulated for efficient correction (scratch removal), polishing, and high-gloss finishing of automobile paint. Suitable for machine polish only

Cutting Compound 300ml
Remove scratches, orange peel, and sandpaper marks with Cutting Compound
Wool buff pad @ 1800rpm

Polishing Compound 300ml
Remove marks from Cutting and bring to a gloss with Polishing CompoundSponge/Euro foam buff pad @ 1500rpm
(if sandpaper marks remain, use wool)

Finishing Compound 300ml
If desired, bring paintwork up to perfection with clear gloss then finish with Finishing Compound
Sponge/Euro 'finishing' foam buff pad @ 1300rpm

Excellent properties with results:

✔ Suitable for all types of automobile paint
✔ Fine ceramic abrasive is highly refined to prevent scratches, marring, and blurring
✔ New anti-clogging, low dust formula improves working conditions
✔ Can be used as a two- or three-step process, as needed
✔ Contain no silicone, gloss-enhancers, or any other unnecessary additives

Contents - 500ml

Features

SOFT99 Leather Cleaner & Conditioner not only safely and efficiently cleans leather without risk of drying or degradation, but also restores and protects leather's natural gloss and sheen, without feeling greasy or sticky.

Direction

To apply, simply spray onto the surface and wipe around with a microfiber cloth.

Allow to dry about 20 minutes after wiping

For perforated leather, apply indirectly by spraying onto the microfiber towel first.

Contents - 1000 ml

Features

Neutral Shampoo has a superb cleaning properties, which prevents dirt and dry suds sticking to the bodywork, even in summer periods you will only need to rinse it once! Shampoo has anion properties which allows it to create crazy amount of suds giving you an additional layer of safe contact with the bodywork. We strongly recommend using the shampoo with our ‘SMOOTH EGG Creamy Soft Sponge’ to fully unleash the potential of this product.

Directions

1. Wet ‘SMOOTH EGG Creamy Soft Sponge’ first.

2. Pour solution directly onto sponge, or put 5 caps of shampoo into a 20L detailing wash bucket.

3. Lather sponge, if washing with bucket, agitate to allow air to create foams.

4. Glide sponge over body surface in horizontal motion, do not travel backward, compress sponge to release more water and suds.

5. If there is dirt on sponge surface simply squeeze to create suds to lift off dirt.

6. Rinse car after completing process.

7. Wipe off all water drops remaining on surface with a clean or absorption towel.
If water drops remain on surface, it may cause spots or stains.

Contents - 180 ml + Microfiber towel

Features

Cleaner design for glass/ceramic coating contains only mild cleaning ingredients. Restoring brightness of coated vehicle body. Symptoms such as water spots, small scratches on door knobs can be easily removed!

Directions

1. Wash off dirt, dust or mud, and wipe off water.

2. Shake bottle well.

3. Pour a coin size amount of  liquid onto included towel.

4. Rub towel onto surface one panel at a time on affected areas.

Contents - 470ml

Features

Direction

1. Wash off any excess dirt beforehand if necessary.

2. Shake well and spray onto wet or dry tires.

3. Wait to dry before driving, or wipe away excess liquid with a cloth.

Contents - 5000ml

Features

Powerful, pH-neutral, and compound-free, this high-powered shampoo lathers into a thick, creamy foam that just melts the dirt away. Professional size and packaging. Despite its powerful foaming ability, this product has been designed with ease of rinsing in mind. May be used on coated vehicles, diluted 1:50. Compatible with water- and air-driven foamers. 

Contents - 20ml

Features

Spot stain remover kit for fabric seat which is effective for removing stubborn stain. Three simple procedure "Wash"→"Rinse"→"Absorb" can remove stain using our exclusive liquid and HPVA sponge. Can remove up to 30 fifty cent coin size stain. * HPVA=Hexagonal Polyvinyl Alcohol

Directions

1. Soak sponge in water and squeeze allowing sponge to become moist.

2. Shake bottle well and apply 5 drops of liquid onto sponge.

3. Press and tap sponge on stained area.
Cleaning liquid will react with stain and loosen it from the fabric fibres.

4. Rinse sponge.

5. Remove stain from fabric seat by using hexagonal side of sponge to absorb. Rotate each side continuously.

6. Rinse sponge and use flat clean side to absorb remaining excess liquid.

Contents - 250ml + 1 Applicator

Features

Suitable for polishing light colour paint. Ultra-fine powder suspended in liquid form to remove deteriorated coatings, marks and light scratches from paint. The included sponge helps achieve a professional-level finish with only hand polishing.

Direction

1. If you use tires, wash off mud or dirt in advance.

2. Hold about 15-25cm away from the tire sidewall and spray evenly.

If applying on leather spray and spread thinly with a dry cloth.

Contents - 300ml

Features

Remove marks from Cutting and bring to a gloss with Polishing Compound

✔ Suitable for all types of automobile paint
✔ Fine ceramic abrasive is highly refined to prevent scratches, marring, and blurring
✔ New anti-clogging, low dust formula improves working conditions
✔ Can be used as a two- or three-step process, as needed
✔ Contain no silicone, gloss-enhancers, or any other unnecessary additives

Recommended Pad & Speed

Sponge/Euro foam buff pad @ 1500rpm
(if sandpaper marks remain, use wool)

Contents - 500ml

Features

A pH neutral shampoo best dedicated for maintaining cars with professional coatings, can be used as a standalone maintenance product. Shampoo causes water to glide off when the car is being rinsed, leaving less water drops behind meaning less drying time. The shampoo produces best results if used in conjunction with other products from the SMOOTH EGG series.

Directions

1. Rinse car with water, remove dust and heavy dirt in order to prevent scratching paint.

2. Pour shampoo into bucket or apply squirt directly onto a sponge, create lather, then wash whole vehicle.

3. Rinse vehicle with water and dry using microfiber towel.

Contents - 500ml

Features

With Stain Cleaner Strong Type, all you need to do is spray and wipe it off. The white powder won't remain on the surface and re-wiping is NOT necessary. It chemically breaks down and gets rid of stubborn dirt, which normal car shampoo couldn't do. Abrasive compounds are NOT included, so it won't damage your car paint. The fresh scent of grapefruit gets rid off bad odor during the process.

Direction

* Remove dirt from the car in advance.

1. Shake the bottle well.

2. Turn the nozzle to <ON>, and spray it on the surface.

3. Wipe it off with a dry, clean cloth.

Contents - 4000ml

Features

pH balanced Iron remover/cleaner designed to dissolve brake dust and iron contaminants upon contact.

Directions

1. Wash off sand, mud or dust prior to spraying.

2. Spray on surface liberally, initially colourless liquid will gradually turn purple/red within approx. 1-4 minutes.

3. Thoroughly rinse treated surface with a strong stream of water. If solution dry on fully, use a stronger jet of water from a pressure washer to remove film.

* When spray over brake disc, it reacts and changes colour.

Rinse away immediately, if left on too long, may cause bad effects for brake disc.

4. Wipe off with clean towel.

Carry out brake test with low gear 2-3 times after cleaning.

* This product is formulated for wheel.

If use for car body, carefully rinse off with water afterwards.

Contents - 300ml

Features

If desired, bring paintwork up to perfection with clear gloss then finish with Finishing Compound

✔ Suitable for all types of automobile paint
✔ Contain no silicone, gloss-enhancers, or any other unnecessary additives

Recommended Pad & Speed

Sponge/Euro 'finishing' foam buff pad @ 1300rpm

Contents - 300ml

Features

Remove scratches, orange peel, and sandpaper marks with Cutting Compound

✔ Suitable for all types of automobile paint
✔ Fine ceramic abrasive is highly refined to prevent scratches, marring, and blurring
✔ New anti-clogging, low dust formula improves working conditions
✔ Can be used as a two- or three-step process, as needed
✔ Contain no silicone, gloss-enhancers, or any other unnecessary additives

Recommended Pad & Speed

Wool buff pad @ 1800rpm

Contents - 100ml

Features

Liquid penetrates effectively between the space of adhesive and bonded surface allowed easy removal of sticky adhesive residues.

Direction

* Cut the end of a nozzle into the desired size. 

1. Shear off the edge of a sticker and spray into gap with a small amount of liquid. Then, using the included spatula rub the sticker until it goes off. 

2. In case any glue residue still remains on the surface, it's best to spray it again and let it soak for a while. Then, using a soft cloth try to rub it off. If the glue residue remains on the surface repeat process until completely removed.

Contents - 1000ml

Features

For cut use a wool pad and foam pad to finish.